Surface Prep Scarifying Scabbling ACE Cutting Equipment & Supply Novi, Michigan MI

SURFACE PREPARATION MACHINES

EDCO SCARIFIERS

EDCO CPM-8

Available for Rental at ACE Cutting Equipment-Novi, MI

EDCO CPM-8 Walk Behind Scarifier
Gasoline
NEW! 8" Push Model

EDCO CPM8 gasoline scarifier new model

Features
Specifications

Features
Edco CPM-8 - 8" Scarifier 9HP Honda engine.

• Up to 8" working width (20 cm.) Up to 1/8" working
  depth per pass (3 mm.)
• Power source over drum to eliminate vibration and   maximize surface contact
• Compact design Front-mounted lifting handle makes   loading and unloading easy
• Vacuum port equipped
• Water misting system standard Ideal for:
   - Sidewalk repair
   - Coating removal
   - Floor preparation or cleaning
   - Creating nonslip surfaces
   - Traffic line removal

• Performance: 350-500 sq. ft./hr - (33-46 sq. m./hr)
at a depth of 1/8" (3 mm.)
• 9 HP Gasoline Honda
• Working Width 8" (20 cm)
• Drum Assembly is Interchangeable
• Cutter Shafts for Drums 6 Drum Rotation Down-cut   Length-38" (97 cm) Width-19" (48 cm) Height-39" (99 cm)
• Weight-250 lbs (92 kg)

EDCO CPM-8 Technical Specifications
Motor
Power Options	9HP Honda gasoline engine

Cutting Equipment
Grinding Width	Up to 8" working width
Grinding Depth	(3 mm.) per pass

Permormance
Concrete Removal	350-500 sq. ft./hr

Blade
Drum Assembly is Interchangeable
Down-cut Length-38" (97 cm) Width-19" (48 cm) Height-39" (99 cm)

Weight
Weight	250 lbs (92 kg)

Ideal for: Sidewalk trip hazard repair Concrete and coatings removal Floor cleaning and/or preparations Creating non-slip surfaces Traffic line and markings removal

EDCO CPM-10

EDCO CPM-10
Gasoline
NEW! 10" Push Model

EDCO CPM10 gasoline scarifier new model

Features
Specifications

EDCO CPM-10 - 10" Scarifier

The new push model CPM-10 features a side loading large drum assembly and a 10" wide cut which removes 3/16"
per pass.

Features:

Side loading large drum assembly
10” wide cut which removes 3/16” per pass
13HP 2-cycle Gas Engine with 1/4” steel frame
Heavy-duty, oversized bearings
Weighs 299 lbs. with cutters
Teathered emergency stop switch
Larger 6” wheels in the rear for easy handling
Gasoline or Electric models available
Vacuum port standard for dust-free cuting
Tungsten carbide or steel cutters available

EDCO CPM-10 Technical Specifications
Motor
Motor	13 hp Honda gasoline engine
Grinding Width	Up to 10"

Cutting Equipment
Working Depth	3/16" per pass
RPM	2446

Dimensions
Large 6" rear wheels	Makes the unit easier to handle

- Features an emergency stop switch for safety
- Side loading drum assembly
- 1 year warranty

EDCO CPU-10

EDCO CPU-10
10" Self Propelled Scarifier - Gasoline
EDCO CPU-10 Scarifier

Features
Specifications

Features:
Edco CPU-10 - 10" Self Propelled Scarifier

10" working width will scarify approximately 500-750 sq. ft. per hour at Depth Per Pass of 1/8"
Adjustable depth control up to 3/16" working depth per pass
Upcut drum rotation and heavyweight construction increases production and lifts even the toughest floor coatings
Hydrostatic transmission with forward and reverse drive provides smooth speed changes and less operator fatigue
Includes lifting bail, oil alert and hour meter
Optional outrigger axle enables the CPU-10(FC)
to follow slab contours closely when working on uneven surfaces
Convertible hood design on CPU-10(FC) allows for multiple drum set-ups and provides easy access for quick drum changes

Ideal for:
- Parking deck and road repairs
- Factory floor preparation or cleaning
- Repairing mall floors

EDCO CPU-10 Technical Specifications
Engine Options
13HP Honda
10HP Electric 230/460V 3 Phase
20HP Honda

Cutting Equipment
Grinding Width	Up to 10" working width
Grinding Depth	1/8" per pass

Permormance
Concrete Removal	500-750 sq. ft./hr

Dimensions	L x W x H: 49 x 24 x 38.5 "

Weight	530 lbs

This unit is ideal for: Parking deck and road repairs Factory floor preparation or cleaning Repairing mall floors

EDCO Model CPU-12

EDCO - Model CPU-12 - Gasoline
12" Self Propelled Scarifier

EDCO CPU12 Scarifier 12" gasoline

Features
Specifications

EDCO CPU-12 - 12" Self-Propelled Scarifier

With a working width to 12", the CPU-12 is for high production use in industrial plants, malls, dairy barns, roads or warehouses.

Features:

Up to 12" working width (30 cm.)
2-cycle Gasoline Engine
Adjustable to 1/4" working depth per pass (6 mm.)
Accommodates EDCO's largest cutters for longer life and more removal
Upcut drum rotation and heavyweight construction provide faster milling action and more uniform surface texture
Hydrostatic transmission with forward and reverse drive provides smooth speed changes and less operator fatigue
Hydraulic-powered engage/disengage lever lowers or raises drum from surface

Ideal for:

Planing concrete, asphalt, epoxies, elastomerics
and masterplate floors with ease
High production use in industrial plants, malls, dairy barns, roads or warehouses

Performance:

1,250-1,500 sq. ft./hr - (116-139 sq. m./hr) at a depth of 1/8" (3 mm.

EDCO CPU-12 Technical Specifications
Engine
Gasoline Engine Specifications	38 hp, 1600 RPM
Propane Engine Specifications	5-1/2 hp, 1740 RPM
Electric Motor Specifications	15 hp, 230V/460V, 2100 RPM

Cutting Equipment
Grinding Width	12"
Working Depth	1/4" per pass (adjustable)
Coverage	1250 to 1500 sq. ft. per hour (at 1/8" depth)

Benefits
- Equipped with a forward/reverse drive
- Hydrostatic transmission system
- Upcut drum action for more rapid milling
- Drum is controlled via hydraulic engagement lever
- 3 power options available
- 1 year warranty

BWM SCARIFIERS

BWM Model SC-8.5

BWM - Model SC 8.5 - Gasoline
The Freedom to Cut Concrete Anywhere!

BW Manufacturing SC8.5 Scarifier gasoline

Features
Specifications

Features: SC-8.5 Scarifier

With the tool-less quick-change cage assembly and choice
of hardened steel cutter, carbide cutters or special milling
flails with tungsten blades, you can change the function of
the machine in only minutes. Uses of the SC 8.5 range
from traffic line removal, sidewalk repairs, coating preparation, removal of epoxy and urethane coatings, creating non-slip surfaces, grinding high spots to cleaning floors of dirt and oils. Uses a 2-cycle Gas engine.

The six-shaft configuration allows for: (1) more cutters per loading and increased grinding action, (2) fewer cutter changes and more production plus (3) smoother drum rotation which leads to less machine vibration.

See Features List

BWM Model SCB-1200

BWM Model SCB-1200 - Turbo Diesel
Ahead of the Competition!

BW Manufacturing SCB1200 Scarifier turbo diesel

Features
Specifications

SCB-1200 Scarifier

After years of research, development and testing, B W Manufacturing, Inc. has produced the only mid-sized ride on scarifying / shotblasting machine in the market today. The SCB-1200 gives you mobility and versatility by being able to switch from scarifying to blasting in just minutes.

With a state of the art scarifying head that is self-leveling to automatically adjust itself to different contours of the
floor or pavement, you will achieve an accurate removal
of thin mill coatings to 1/4” overlays. The SCB-1200 is
ideal for use on rubber membranes, mastics, epoxy
coatings, and line stripes.

The SCB-1200 scarifier will put you ahead of the
competition with its production rates and it’s
vacuum/collector system that eliminates dust and
removes all material from the surface it is scarifying.

Versatility is the key to the SCB-1200 scarifier. With quick-
change cages allowing you to go from steel to carbide
cutters and to different cutting width cages in just minutes.

Designed with the operator in mind, the SCB-1200
scarifier has easy to turn manual steering and
ergonomically designed one- handed controls, along
with a removable dust containment box with wheels for
ease of dumping.

Using the latest technology in EPA approved liquid cooled
diesel engines and catalytic converter, you are far below
any minimal emissions standards. With the use of state of
the art components, compressors, electronic pulsation,
hydraulics, and drives, the SCB-1200 is the most reliable
and productive mid-sized surface preparation machine on
the market today.

See Features List

Scarifier Machines

Scarifying machines apply a cutting wheel to the concrete surface. EDCO’s exclusive 6-shaft cutting drum flails the surface, leaving a clean, textured or roughened finish. Scarifiers are also referred to as planers, milling machines, rotary cutters or simply surface-preparation machines. These versatile machines have various styles of interchangeable cutter assemblies that can be used for cleaning, grinding and light or heavy milling. Production rates range from 350
to 1,500 square feet per hour (dependent on machine size and horsepower) for a 1/8-inch removal depth of 3,500 PSI concrete.

SURFACE PREPARATION MACHINES

EDCO SCABBLERS

Scabbler Machines

Scabblers use compressed air to hammer piston-mounted bits into the concrete surface roughening the concrete surface more than grinding or scarifying. EDCO’s Chip-Dek Scabbler can remove up to 1/4 inch of concrete surface in a single pass. The actual production rate depends on the strength of the concrete. A typical removal rate for a machine with a 12-inch working width is 200 to 250 square feet per hour at a 1/8-inch depth.

EDCO Model CD-3

EDCO - Model CD-3 - Air Powered
3 Headed Scrabbler

EDCO CD3 3 Headed Scabbler

Features
Specifications

CD-3 – Air-Powered, 3 Headed Scabbler

Features:

Delivers 1,200 hits per minute for fast surface removal
Requires only 100 CFM at 100 PSI
Heavy-duty 1/4" steel frame
2" Vacuum Port for dust-free operation
Automatic in-line oiler
WHIPCHEK Cable assures safe air hose hookup

Ideal for:

Removing spalling concrete
Roughening surfaces for new overlayments
Reducing high spots
Creating wheelchair access ramps
Removing epoxy
Creating slip-resistant surfaces
Texturing parking garage ramps
Removing loose or deteriorated concrete

Performance:

3 Scabbler heads remove 3/16" concrete per pass

See Features List

EDCO Model CD-5

EDCO - Model CD-5 - Air Powered
5 Headed Scrabbler

EDCO CD5 5 Headed Scabbler

Features
Specifications

CD-5 – Air-Powered, 5 Headed Scabbler

Features:

Delivers 1,200 hits per minute for fast surface removal
Requires only 160 CFM at 100 PSI
Heavy-duty 1/4" steel frame
Wide T-Grip Handle and 8" wheels for superior balance and handling
3" Vacuum Port for dust-free operation
Automatic in-line oiler
WHIPCHEK Cable assures safe air hose hookup

Ideal for:

Removing spalling concrete
Roughening surfaces for new overlayments
Reducing high spots
Creating wheelchair access ramps
Removing epoxy
Creating slip-resistant surfaces
Texturing parking garage ramps
Removing loose or deteriorated concrete

Performance:

5 Scabbler heads provide 11 1/2" working width Remove up to 250 square feet of concrete per hour

See Features List

EDCO Scarifier - Carbide, Steel & Tungsten Cutters

CPM-4 Accessories

Carbide Cutters

CP206-T #20156

1 3/4" OD x 5/8" ID x 1/4" Six point cutter, maximum cutter shaft 1/2". Long lasting, fast milling of concrete, asphalt or coatings.

CP205-T #20256

1 3/4" OD x 5/8" ID x 1/4" Five point cutter, maximum cutter shaft 1/2". Long lasting, fast milling of concrete, asphalt or coatings.

Steel Cutters

CP305 #20206

2" OD x 5/8" ID x 3/16"
12 teeth cutter, flat tip. General purpose removal of concrete or asphalt.

JRS501-P #12206

2" OD x 17/32" ID x 3/16"
18 teeth, pointed. Lightly scarify, clean surfaces, remove traffic lines

CPM-10 Cutters

Carbide Cutters - 6 Shaft Drum

CP308-T #20326

2 1/4" OD x 25/32" ID x 1/4" Six point cutter, long lasting, fast milling of concrete, asphalt or coatings.

Steel Cutters - 6 Shaft Drum

Scarifier carbide cutters 6 shaft drum 2"

CP305 #20206

2" OD x 5/8" ID x 3/16" 12 teeth cutter, flat tip. General purpose removal of concrete or asphalt.

Carbide Cutters - 8 Shaft Drum

CP206-T #20156

1 3/4" OD x 5/8" ID x 1/4" Six point cutter, maximum cutter shaft 1/2". Long lasting, fast milling of concrete, asphalt or coatings.

CPU-12 Cutters

Carbide Cutters

CP408-TV #20136

3 1/8" OD x 1 3/16" ID x 5/16" Eight point heavy duty cutter with oversized inner diameter. Max. cutter shaft 1" diameter. For heavy removal of concrete, asphalt or coatings

Steel Cutters

CP405 #20086 & CP 405-6 #20166

3" OD x 1" ID x 3/16"
15 teeth, flat tip. General purpose removal of concrete or asphalt.

CP405-P #20056

3" OD x 1" ID x 3/16"
15 teeth, pointed. Lightly scarify, remove laitance, clean surfaces.

Scarifier - Steel Cutters

CPM-8 Accessories

Carbide Cutters

CP206-T #20156

1 3/4" OD x 5/8" ID x 1/4" Six point cutter, maximum cutter shaft 1/2". Long lasting, fast milling of concrete, asphalt or coatings.

CP205-T #20256

1 3/4" OD x 5/8" ID x 1/4" Five point cutter, maximum cutter shaft 1/2". Long lasting, fast milling of concrete, asphalt or coatings.

Steel Cutters

CP305 #20206

2" OD x 5/8" ID x 3/16"
12 teeth cutter, flat tip. General purpose removal of concrete or asphalt.

JRS501-P #12206

2" OD x 17/32" ID x 3/16"
18 teeth, pointed. Lightly scarify, clean surfaces, remove traffic lines or remove coatings.

CPU-10(FC) Cutters

Carbide Cutters

Model CPU-10-FC (4 shaft drum)

CP408-TV #20136

3 1/8" OD x 1 3/16" ID x 5/16" Eight point heavy duty cutter with oversized inner diameter. Max. cutter shaft 1" diameter. For heavy removal of concrete, asphalt or coatings

Models CPU-10-FC (6 shaft drum)

CP308-T #20326

2 1/4" OD x 25/32" ID x 1/4" Six point cutter, long lasting, fast milling of concrete, asphalt or coatings.

Steel Cutters

Model CPU-10-FC (6 shaft drum)

CP404 #20076

2 3/8" OD x 1" ID x 3/16"
15 teeth, flat tip. General purpose removal of concrete or asphalt.

CP404-P6 #20296

2 3/8" OD x 1" ID x 3/16"
15 teeth, pointed. Lightly scarify or clean surfaces.

Models CPU-10-FC (4 shaft drum)

CP405 #20086 & CP 405-6 #20166

3" OD x 1" ID x 3/16"
15 teeth, flat tip. General purpose removal of concrete or asphalt.

CP405-P #20056

3" OD x 1" ID x 3/16"
15 teeth, pointed. Lightly scarify, remove laitance, clean surfaces.

Tungsten Carbide Cutters

Models CPM-4 & CPM-8

CP206-T #20156

1 3/4" OD x 5/8" ID x 1/4"
Six point cutter, maximum cutter shaft 1/2". Long lasting, fast milling of concrete, asphalt or coatings.

CP205-T #20256

1 3/4" OD x 5/8" ID x 1/4"
Five point cutter, maximum cutter shaft 1/2". Long lasting, fast milling of concrete, asphalt or coatings.

CP207-T

1 1/2" OD x 1/2 ID x 1/2"
Seven point special milling (solid carbide) cutter. Long lasting cutter that removes traffic markings and soft coatings.

Model CPU-10-C (6 shaft drum)

CP508-TV #20306

2 5/8" OD x 1" ID x 3/16"
Eight point cutter, long lasting, fast milling of concrete, asphalt or coatings.

CP404-TV #20286

2 1/8" OD x 1" ID x 1/4"
Six point cutter, long lasting, fast milling of concrete, asphalt or coatings.

Models CPU-10, CPU-12, CP-SX & CP-TX (6 shaft drum)
CPU-10-C (4 shaft drum)

CP408-TV #20136

3 1/8" OD x 1 3/16" ID x 5/16"
Eight point heavy duty cutter with oversized inner diameter. Max. cutter shaft 1" diameter. For heavy removal of concrete, asphalt or coatings

Model CPM-10 (6 Shaft Drum)

CP206-T #20156

1 3/4" OD x 5/8" ID x 1/4"
Six point cutter, maximum cutter shaft 1/2". Long lasting, fast milling of concrete, asphalt or coatings.

Model CPM-10 (8 Shaft Model)

CP308-T #20326

2 1/4" OD x 25/32" ID x 1/4" Six point cutter, long lasting, fast milling of concrete, asphalt or coatings.

Scarifier Cage Removal & Installation

Cage Removal/Installation	Cage with Carbide Cutters	Cage with Steel Cutters

EDCO Scabbler Cutters

Scabbler Accessories

5-Point Bit

The 5-Point Bit penetrates the surface up to 1/4" per pass and leaves a rough texture.

Ideal for

Breaking up blistered or spalling concrete
Removing floor coatings
Roughening the surface to create a bond for repairs or overlays
General Surface Removal

9-Point Bit

The 9-Point Bit penetrates the surface up to 1/8" per pass and leaves a medium texture.

Ideal for

Creating excellent bonding texture for thin overlays of polymer concrete, epoxy or urethane
Leveling uneven joints
Surface removal for repairing spalled and deteriorated slabs

Scabbler Bit Removal Tool

This bit removal slide hammer will assist you in removing your old bits from either Scabbler.

How to Use a Scabbler

EDCO Scabblers are easy to use. The operator moves the scabbler back and forth using a side to side motion over the surface until the concrete is roughened or removed. A scabbler is the ideal machine for roughening surfaces for new overlays, creating wheelchair access ramps, creating non-slip surfaces and removing loose or deteriorating concrete.

Scabbler accessories include 5-Point and 9-Point Tungsten Carbide Bits. These scabbler bits pound the concrete surface by delivering 1,200 hits per minute. The 5-Point bit leaves a rough textured surface while the 9-Point bits leaves a medium textured surface.

FLOOR PREPARATION & POLISIHERS

Concrete Polishing Interview with Josh Vander Veen of Husqvarna
http://www.youtube.com/watch?v=ryqM3UOuZPI

Surface Prep - How To apply GM 3000 with Josh Van Vander Veen of Husqvarna
http://www.youtube.com/watch?v=JPsd17tRXJ0

We're Leading the Industry!

The Concrete Polishing Association is the only non-biased non-profit trade organization in our industry. The purpose..... to build and maintain a high level of standards, increase awareness, and create desire for concrete when processed to a polished finish. Through education, we will lead to a stronger and more profitable industry.

The Concrete Polishing Association has defined industry standards, developed ethical guidelines, created non-biased specifications, and worked with many leading contractors to develop practical procedures that produce quality, processed concrete floors.

Husqvarna PG 820 - SURFACE PREP

Husqvarna PG 820
Floor Surface Preparation & Polisher

Available for Rental at ACE Cutting Equipment-Novi, MI

Husqvarna PG 820 Surface Preparation Polisher

Features
Specifications

Husqvarna PG 820- Floor Surface Prep & Polisher

The Husqvarna PG 820 is the largest in the
range of surface preparation and finishing
machines. Equipped with Dual Drive Technology™
the PG 820 is among the market's most powerful
and efficient machines.

FEATURES:

• Applications range from concrete floor preparation
   and repair to grinding and polishing of concrete floors
   as well as the repair and polishing of terrazzo and
   other natural stone.
• High power machinery capable of delivering
   extremely high production rates, increasing
   profit and saving valuable time.
• Dual Drive Technology™- A unique patented twin
   motor arrangement with separate motors for grinding
   discs and planetary which enables total control of
   heads speed and direction. This increases
   production rates, enhances operator control
   and allows for a wider range of applications,
   compared to any other planetary machine.
• The ultimate choice for professional flooring contractors
• Triple-headed grinder – more downward pressure and
   power can be delivered to grinding heads. More stable
   operation over undulating surfaces.
• Wide grinding path
• Long machinery service life thanks to the 5-way sealing
   mechanism, the spring steel head system and all
   zinc-plated steel parts.
• Gear-driven planetary head; premium quality belt for
   powering grinding heads.
• Industrial strength construction (robust steel frame,
   strong single-piece aluminium cover.
• Low tool and maintenance cost per square foot.

Model PG 820 - Floor Surface Preparation & Polisher

PG 820 Specifications
Engine
Power output	17 hp
Rated current, A	32 A
Voltage	380 / 480 V
Phases	3

Specs
Grinding width	32"

Dimensions
Weight	970 lbs